山東GRC構件具有總量小，強度高、抗凍融性好、可塑性強、裝飾造型豐富多樣的優點，廣泛的用于新建外裝飾、舊樓改造、外墻造型掛板、園林配景。下面來講講有關GRC構件的行業小知識吧。

Shandong GRC components have the advantages of small total amount, high strength, good frost and thaw resistance, strong plasticity and rich and diverse decorative shapes. They are widely used for new external decoration, old building renovation, external wall modeling hanging plate and garden landscape. Let's talk about the industry knowledge of GRC components.

GRC制品及其連接件應具有足夠的強度、剛度及穩定性。GRC制品工程在進行結構設計計算時，應作為非結構構件，不參與主體結構承載分析，但應按相關的規范規定，進行合理的構件設計，避免對主體結構的不利影響。GRC構件

GRC products and their connectors shall have sufficient strength, rigidity and stability. GRC products engineering shall be regarded as non structural members during structural design and calculation, and shall not participate in the bearing analysis of the main structure. However, reasonable member design shall be carried out according to relevant specifications to avoid adverse impact on the main structure. GRC component

根據破壞后的嚴重程度，GRC制品工程劃分為三個等級。設計時應根據具體情況，按照有關的規定，選用相應的等級。

According to the severity of damage, GRC product engineering is divided into three safety levels. During design, corresponding safety levels shall be selected according to specific conditions and relevant regulations.

1.GRC一般裝飾制品結構設計時除應進行制品本身的強度及剛度驗算外，還應對連接部位進行承載力驗算，如錨固強度、局部承壓等。

1. In the structural design of GRC general decorative products, in addition to checking the strength and rigidity of the products themselves, the bearing capacity of the connecting parts shall also be checked, such as anchorage strength and local bearing capacity.

2.詳細計算方法應參照有關規定執行。

2. The detailed calculation method shall refer to relevant regulations.

3.GRC外墻板的結構設計：GRC外墻板結構設計時除應進行GRC外墻板的強度、剛度驗算和與背負式鋼架連接處的承載力驗算外，還應對背負式鋼架本身進行各桿件的強度剛度驗算：對背負式鋼架與主體結構的連接也應進行承載力驗算。

3. Structural design of GRC exterior wall panel: in the structural design of GRC exterior wall panel, in addition to the strength and rigidity checking calculation of GRC exterior wall panel and the bearing capacity checking calculation of the connection with the piggyback steel frame, the strength and rigidity checking calculation of each member of the piggyback steel frame shall also be carried out: the bearing capacity checking calculation shall also be carried out for the connection between the piggyback steel frame and the main structure.

GRC構件的安裝要求

Installation requirements for GRC components

1、構件安裝要求橫向平整、豎向垂直、整體上線、花飾組對完整、曲線圓滑流暢，構件表面無缺損。

1. The installation of components shall be horizontal and vertical, the overall upper line, the floral assembly shall be complete, the curve shall be smooth and smooth, and the component surface shall be free of defects.

2、構件安裝節點對位準確，防止因埋件錯位導致構件強扭就位，產生安裝應力而日久變形。

2. The alignment of the component installation nodes is accurate, so as to prevent the strong torsion of the component in place due to the dislocation of the embedded parts, and the installation stress and long-term deformation.

3、構件連接點須連接到位，不得遺漏。螺栓連接須帶緊擰靠。

3. The connection points of components must be connected in place without omission. Bolt connection must be tightened.

4、構件接頭順暢，接縫小于10mm。

4. The joints of components shall be smooth and the joints shall be less than 10mm.

5、豎向構件應避免將上部構件層層疊壓在底部構件上，而應將每一截構件單獨懸掛安裝在墻體上。

5. The vertical members shall avoid stacking the upper members on the bottom members layer by layer, and each section of members shall be hung and installed on the wall separately.

6、構件安裝完畢，應自上而下將表面的灰塵和污漬清掃干凈，勾縫飽滿、打磨平整。

6. After the components are installed, the dust and dirt on the surface shall be cleaned from top to bottom, and the joints shall be full and polished.

GRC建筑裝飾構件的種類、規格、圖案，以人為本。構件按照業主的要求設計制作而成，盡管品種規格不一，但在生產過程中全部埋入安裝構件，施工時膨脹螺栓固定，省時、省工、省力，降低成本，減少費用。有需求就來我們網站http://www.nyqaac.com咨詢。

The types, specifications and patterns of GRC building decoration components are people-oriented. The components are designed and manufactured according to the requirements of the owner. Although the varieties and specifications are different, all the components are embedded and installed in the production process. The expansion bolts are fixed during construction, which saves time, labor and labor, and reduces costs and expenses. Come to our website if you need http://www.nyqaac.com consulting service