我們?cè)谘b修房屋的時候都會使用一些工具和一些構件，這其中就有山東GRC構件，這些構件能使房屋看起來更加的一體化，看著更加的立體，這些構件在使用的時候會有一些縫隙，這些問題怎樣處理呢？

When we decorate the house, we will use some tools and some components, including Shandong GRC components. These components can make the house look more integrated and three-dimensional. These components will have some gaps when they are used. How to deal with these problems?

1、在安裝前要確定好安裝位置，畫好基準線。再按照基準線進行安裝，注意調整水平度和垂直度。

1. Before installation, the installation position shall be determined and the datum line shall be drawn. Then install according to the datum line, and pay attention to adjusting the levelness and perpendicularity.

2、GRC窗套安裝：將窗套線沿著窗框外的墻體安裝，注意漲栓緊固位置要避開抹灰層。豎向窗邊線或柱子安裝到每一樓層標高時，要注意調整垂直誤差。標高誤差控制在3mm以?xún)?nèi)。

2. GRC window sleeve installation: install the window sleeve line along the wall outside the window frame, and pay attention to the fastening position of the expansion bolt to avoid the plastering layer. When installing the vertical window sideline or column to the elevation of each floor, pay attention to adjusting the vertical error. The elevation error shall be controlled within 3mm.

3、GRC內有鋼骨架橫向構件，安裝前先在墻體上固定角碼或角鋼，作為與鋼骨架的焊接點。所有焊接點焊縫寬度不少于5mm，長度不少于連接筋直徑的4倍，全部焊渣。構件的焊接點均應涂紅丹防銹漆打底面涂銀色油漆。

3. There are transverse members of steel skeleton in GRC. Before installation, angle pieces or angle steels shall be fixed on the wall as welding points with the steel skeleton. The weld width of all welding points shall not be less than 5mm, and the length shall not be less than 4 times of the diameter of the connecting bar. All welding slag shall be removed. The welding points of components shall be painted with red lead antirust paint, and the priming surface shall be painted with silver paint.

構件斷面尺寸大于300mm小于1000mm(沒有鋼骨架的)的安裝時，在保溫層上劃出埋件位置，角磨機切開保溫，用漲栓將GRC水泥構件預埋鍍鋅埋件與墻體緊固，做好節點防腐處理，修補接縫。

When installing components with a section size of more than 300mm but less than 1000mm (without steel framework), mark the position of embedded parts on the insulation layer, cut the angle grinder for insulation, use expansion bolts to fasten the embedded galvanized embedded parts of GRC cement components with the wall, do a good job in node anti-corrosion treatment, and repair the joints.

斷面尺寸小于300mm的構件，直接用加長漲栓穿過保溫層緊固到墻體上，注意保證螺栓的錨固長度。

For members with section size less than 300 mm, the extended expansion bolt shall be directly used to pass through the insulation layer and be fastened to the wall. Attention shall be paid to ensuring the anchor length of the bolt.

4、GRC構件與構件之間的接縫處理：GRC水泥構件外表的接縫，應平整、光滑。使用專用修補材料填充縫隙或進行回填?；靥畹哪康氖前袵RC構件與主體連接成一個整體，防止與主體間的接縫開裂。

4. Joint treatment between GRC components: the joints on the surface of GRC cement components shall be flat and smooth. Use special repair materials to fill gaps or backfill. The purpose of backfilling is to connect GRC components with the main body as a whole, so as to prevent the joints between GRC components and the main body from cracking.

另外，回填時，需要對回填面的所有廢渣雜物干凈，淋透水后才能回填，并用鋼筋或竹竿翻插回填料使其密實，不能有空殼。大飾線回填料需使用陶?；炷粱蚺蛎浾渲閹r做底層GRC填充料，應馬上處理好回填構件的結合縫。

In addition, during backfilling, all waste residues and sundries on the backfilling surface shall be removed, and the backfilling can only be carried out after being drenched with water. Reinforcing bars or bamboo poles shall be used to turn and insert the filler back to make it dense without empty shells. Ceramsite concrete or expanded perlite shall be used as the GRC filler for the bottom layer of the large decorative line backfill, and the joint of the backfill component shall be treated immediately.

飾線、柱頂?shù)葮?gòu)件的回填面還得按8%找坡水泥膏壓光，做到光滑不能有積水。

The backfilling surface of trim line, column top and other components shall be polished with 8% slope making cement paste to make it smooth and free of water.

5、GRC收口部位的處理，如對女兒墻壓頂、窗臺板、窗下墻等部位，要做到美觀、防水，嚴格按照工藝施工(由土建施工單位做泛水)。

5. The GRC closure parts, such as the coping of the parapet, the sill plate, the wall under the window and other parts, shall be beautiful and waterproof, and shall be constructed in strict accordance with the process (the civil construction unit shall do flashing).

6、GRC清潔收尾：清潔收尾是工程竣工驗收前的一道工序，雖然安裝已完工，但為保證飾面質量，此工序更不能馬虎。并在全過程中注意成品保護，以便進入下道表面噴涂施工。

6. GRC cleaning and finishing: cleaning and finishing is a process before the completion acceptance of the project. Although the installation has been completed, this process should not be sloppy to ensure the quality of the finish. Pay attention to the protection of finished products in the whole process to facilitate the next surface spraying construction.

GRC構件的安裝問題好，處理縫隙的問題才是困擾人們的一大難題，以上這些便是為大家整理的一些處理方法，希望可以幫助到你。更多相關內容就來網站http://www.nyqaac.com咨詢吧！

The installation of GRC components is easy to solve, and the problem of dealing with gaps is a big problem that troubles people. These are some solutions for you, and I hope they can help you. More relevant content will come to the website http://www.nyqaac.com Consult!